JIS G 3116: 2000 Steel sheets, plates and strips for gas cylinders. Japanese Industrial Standard

21 стр. The European Standard EN 10246-10:2000 has the status of a British Standard April 2000 This part of EN 10246 specifies the requirements for radiographic X-ray testing of the longitudinal or helically weld seams of automatic fusion arc-welded steel tubes for the detection of imperfections. The standard specifies acceptance levels and calibration procedures. European Standard EN 10246, Non-destructive testing of steel tubes, comprises the p...

14 cтр. The European Standard EN 10246-12:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements and the acceptance levels for magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections. This part of EN 10246 is to be used for the detection of surface imperfections on the entire or any part of the outer surface of tubes, excluding the e...

10 cтр. The European Standard EN 10246-13:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements for the full peripheral ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc welded (SAW) tubes, for wall thickness measurement. The standard specifies acceptance levels and calibration procedures. NOTE 1: Full peripheral testing does not necessarily mean that 100...

16 стр. The European Standard EN 10246-16:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the ultrasonic testing of the area adjacent to the weld of welded steel tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE: This inspection may alternatively, in accordance with EN 10246-15, be carried out on longitudinal edges of...

12 стр. The European Standard EN 10246-17:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30...

16 cтр. The European Standard EN 10246-2:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for automatic eddy current testing of seamless and welded austenitic and austenitic-ferritic steel tubes with the exception of submerged arc-welded (SAW) tubes for verification of hydraulic leak-tightness. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations...

14 стр. The European Standard EN 10246-9:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements for the automatic ultrasonic testing of the weld seam of submerged arc-welded (longitudinally or helically) tubes for the detection of imperfections oriented predominantly parallel to and/or at right angles to the weld seam. The standard specifies acceptance levels and calibration procedures. European S...

This European Standard was approved by CEN on 3 February 2000. 14p. This standard specifies the shape, dimensions and tolerances of cast concrete test specimens in the form of cubes, cylinders and prisms, and of the moulds required to produce them.

114 cтр. The European Standard EN 12516-1:2005 has the status of a British Standard This European Standard was approved by CEN on 15 March 2005. This document (EN 12516-1:2005) has been prepared by Technical Committee CEN/TC 69 Industrial valves, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October...

This European Standard was approved by CEN on 23 May 2002. Amendment A1 was approved by CEN on 12 May 2005. 18p. This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials (but initially restricted to steel) with a view to ensure safe operation.