API RP 1168-2008 Pipeline Control Room Management

01 Административный регламент от 29.06.2009 № 172 02 Административный регламент от 04.09.2007 № 606 03 Административный регламент от 29.02.2008 № 112 04 Административный регламент от 14.12.2007 № 858 05 Административный регламент от 30.10.2008 № 280 06 Административный регламент от 30.07.2009 № 237 07 Административный регламент от 30.06.2009 № 202 08 Административный регламент от 30.10.2008 № 281 09 Административный регламент от 23.10.2008 № 266...

API 551 (1993)_Process Measurement Instrumentation.pdf ( 4206 KB) API 552 (1994)_Transmission Systems.pdf (3162 KB) API 553 (1998)_Refinery Control Valves.pdf (413 KB) API 554 (1995)_Process Instrumentation and Control.pdf (5545 KB) API 555 (2001)_Process Analyzers.pdf (3633 KB) API 556 (1997)_Instrumentation and Control Systems.pdf (2423 KB) API 557 (2000)_Guide To Advanced Control Systems.pdf (2867 KB) API 560 (2001)_Fired Heaters f...

30 стр. American Petroleum Institute, Fifth Edition, June 2007 This Recommended Practice (RP) provides guidelines for pressure testing steel pipelines for the transportation of gas, petroleum gas, hazardous liquids, highly volatile liquids or carbon dioxide. The RP provides guidance so that: a. Pipeline operators can select a pressure test suitable for the conditions under which the test will be conducted. This includes, but is not limited to, pi...

American Petroleum Institute (API) Third Edition, January 2007. 46p. The purpose of this recommended practice is to present procedures and practices for achieving effective corrosion control on aboveground storage tank bottoms through the use of cathodic protection. It contains provisions for the application of cathodic protection to existing and new storage tanks. Corrosion control methods based on chemical control of the environment or the use...

This European Standard was approved by CEN on 1 August 2002. 16p. This standard establishes an experimental method of assessing the strength of valve shells by applying an elevated hydrostatic pressure test at room temperature.

На английском и французском языках. 26 стр. Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-4: Particular requirements – Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9 Mat?riel ?lectrique de mesure, de commande et de laboratoire – Exigences relatives...

Contents: IEEE Std 828-1990. IEEE Standard for Software Configuration Management Plans. ANSI/IEEE Std 1042-1987. An American National Standard. IEEE Guide to Software Configuration Management. ANSI/IEEE Std 1058.1-1987 (Reaffirmed 1993). An American National Standard. IEEE Standard for Software Project Management Plans. IEEE Std 1074-1991. IEEE Standard for Developing Software Life Cycle Processes.

2009г. , 2082 стр. Язык: английский Данный стандарт является переработанным стандартом IEEE 802.16-2004 и объединяет материалы из IEEE Std 802.16e-2005, IEEE 802.16-2004/Cor1-2005, IEEE 802.16f-2005 и IEEE Std 802.16g-2007. This standard specifies the air interface, including the medium access control layer (MAC) and physical layer (PHY), of combined fixed and mobile point-to-multipoint broadband wireless access (BWA) systems providing multiple...

This preface as well as all footnotes and annexes are included for informational purposes and are not part of ANSI/ISA-88.01-1995. This standard has been prepared as part of the service of the ISA, the international society for measurement and control, toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should be subject to periodic review. Toward this end, the Society welcomes...

57 стр. NACE International This standard covers the NACE external corrosion direct assessment (ECDA) process for buried onshore ferrous piping systems. This standard is intended to serve as a guide for applying the NACE ECDA process on typical pipeline systems. This standard was written to provide flexibility for an operator to tailor the process to specific pipeline situations. ECDA is a continuous improvement process. Through successive applica...