API Std 2000-1982 Venting Atmospheric and Low-Pressure Storage Tanks

API Std 2000-1982 Venting Atmospheric and Low-Pressure Storage Tanks
  • разное
  • pdf
  • 1.66 МБ
  • добавлен 03.02.2012
American Petroleum Instltute (API) Third Edition, January 1982. 18p. This standard covers the normal and emergency venting requirements for aboveground liquid petroleum storage tanks and aboveground and belowground refrigerated storage tanks designed for operation at pressures form 1/2 ounce per square inch vacuum through 15 pounds inch gage.

Смотрите также


ANSI/API Std 2015-2001 Requirements for Safe Entru and Cleaning of Petroleum Storage Tanks

ANSI/API Std 2015-2001 Requirements for Safe Entru and Cleaning of Petroleum Storage Tanks

  • разное
  • pdf
  • 4.68 МБ
  • добавлен 02.02.2012
American Petroleum Institute (API) Sixth Edition, August 2001. 58p. This standard is applicable to cleaning stationaru atmospheric and lov-pressure (up to and including 15 psig) aboveground petroleum storage tanks used in all sectors of the petroleum and petrochemical industry, including crude oil and gas production, refineries,...
API Std 653-2009 Tank Inspection, Repair, Alteration, and Reconstruction

API Std 653-2009 Tank Inspection, Repair, Alteration, and Reconstruction

  • разное
  • pdf
  • 2.09 МБ
  • добавлен 03.02.2012
American Petroleum Instltute (API) Fourth Edition, April 2009. 166p. This standard covers steel storage tanks built to API 650 and its predecessor API 12C. It provides minimum requirements for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, ...
API RP 520-1-2000 Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part I - Sizing and Selection

API RP 520-1-2000 Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part I - Sizing and Selection

  • разное
  • pdf
  • 1015.88 КБ
  • добавлен 06.02.2012
American Petroleum Instltute (API) Seventh Edition, January 2000. 100p. This recommended practice applies to the sizing and selection of pressure relief devices used in refineries and related industries for equipment that has a maximum allowable working pressure of 15 psig [103 kPag] or greater.
API Std 526-2002 Flanged Steel Pressure Relief Valves

API Std 526-2002 Flanged Steel Pressure Relief Valves

  • разное
  • pdf
  • 435.38 КБ
  • добавлен 03.02.2012
American Petroleum Instltute (API) Fifth Edition, June 1995. 23p. This standard is a purchase speciЮcation for Яanged steel pressure relief valves. Basic requirements are given for direct spring-loaded pressure relief valves and pilot-operated pressure relief valves.
API RP 2A-WSD-2002 Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms - Working Stress Design

API RP 2A-WSD-2002 Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms - Working Stress Design

  • разное
  • pdf
  • 2 МБ
  • добавлен 06.02.2012
American Petroleum Instltute (API) Twenty-First Edition, December 2000, Errata and Supplement 1, December 2002. 242p. This publication serves as a guide for those who are concerned with the design and construction of new platforms and for the relocation of existing platforms used for the drilling, development, and storage of hyd...
API Std 1631-2001 Interior Lining and Periodic Inspection of Underground Storage Tanks

API Std 1631-2001 Interior Lining and Periodic Inspection of Underground Storage Tanks

  • разное
  • pdf
  • 1.94 МБ
  • добавлен 02.02.2012
American Petroleum Institute (API) Fifth Edition, June 2001. 30p. The following definitions are applicable to underground tank lining and inspection as described in this standard.
API RP 520-2-2003 Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part II - Installation

API RP 520-2-2003 Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part II - Installation

  • разное
  • pdf
  • 539.41 КБ
  • добавлен 06.02.2012
American Petroleum Instltute (API) Fifth Edition, August 2003. 42p. This recommended practice covers methods of installation for pressure-relief devices for equipment that has a maximum allowable working pressure (MAWP) of 15 psig (1.03 bar g or 103 kPA) or greater
API Std 510-2006 Pressure Vessel Inspection Code In-Service Inspection, Rating, Repair and Alteration

API Std 510-2006 Pressure Vessel Inspection Code In-Service Inspection, Rating, Repair and Alteration

  • разное
  • pdf
  • 2.81 МБ
  • добавлен 05.02.2012
American Petroleum Instltute (API) Ninth Edition, June 2006. 20p. This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure-relieving devices protecting these vessels.
API RP 581-2008 Risk-Based Inspection Technology

API RP 581-2008 Risk-Based Inspection Technology

  • разное
  • pdf
  • 5.98 МБ
  • добавлен 06.02.2012
American Petroleum Instltute (API) Second Edition, September 2008. 654p. This publication provides quantitative procedures to establish an inspection program using risk-based methods for pressurized fixed equipment, including pressure vessel, piping, tankage, pressure relief devices, and heat exchanger tube bundles. This documen...
ANSI/API Std 521-2007 Pressure-relieving and Depressuring Systems, ISO 23251 (Identical)

ANSI/API Std 521-2007 Pressure-relieving and Depressuring Systems, ISO 23251 (Identical)

  • разное
  • pdf
  • 4.06 МБ
  • добавлен 06.02.2012
American Petroleum Instltute (API) Fifth Edition, January 2007. 202p. This International Standard is applicable to pressure-relieving and vapour-depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oi...