Стандарты Британии (BS)
Стандарт
  • формат pdf
  • размер 1.5 МБ
  • добавлен 03 февраля 2012 г.
BS EN ISO 1461-2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods
24 pages
This Inteational Standard specifies the general properties of coatings and test methods for coatings applied by dipping fabricated iron and steel articles (including certain castings) in a zinc melt (containing not more than 2 % of other metals). It does not apply to the following:
a) sheet, wire and woven or welded mesh products that are continuously hot dip galvanized;
b) tube and pipe that are hot dip galvanized in automatic plants;
c) hot dip galvanized products (e.g. fasteners) for which specific standards exist and which might include additional requirements or requirements which are different from those of this Inteational Standard.
NOTE Individual product standards can incorporate this Inteational Standard for the coating by quoting its number, or can incorporate it with modifications specific to the product. Different requirements can also be made for galvanized coatings on products intended to meet specific regulatory requirements.
After-treatment/over-coating of hot dip galvanized articles is not covered by this Inteational Standard.
This document (EN ISO 1461:2009) has been prepared by Technical Committee ISO/TC 107 "Metallic and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 "Metallic and other inorganic coatings", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn at the latest by November 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1461:1999.
According to the CEN/CENELEC Inteal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austna, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Возможность скачивания данного файла заблокирована по требованию правообладателя.
Смотрите также

Сборник стандартов ISO

  • формат pdf
  • размер 43 МБ
  • добавлен 29 сентября 2010 г.
ISO 3:1973 Предпочтительные числа. Ряды предпочтительных чисел ISO 7-1:1994 Резьбы трубные, обеспечивающие герметичность соединения. Часть 1. Размеры, допуски и обозначения ISO 83:1976 Сталь испытание на удар по Шарпи (u-образный надрез) ISO 148-1:2006 Металлические материалы Испытание на ударную прочность маятниковым копром по Шарпи. ?Часть 1: Метод испытаний. ISO 228-1:2000 Резьбы трубные, не обеспечивающие герметичность соединения. Часть...

Стандарт ISO 3913-1977 (E). Shipbuilding - Welded steel bollards

standart
  • формат pdf
  • размер 808.5 КБ
  • добавлен 23 марта 2011 г.
Стандарт на изготовление швартовных кнехтов. На английском языке.

ISO 1518 Paints and varnishes Scratch test (Лаки и краски. определение твердости покрытия)

Стандарт
  • формат pdf
  • размер 303.95 КБ
  • добавлен 08 декабря 2011 г.
Настоящий стандарт был утвержден еврапейским комитетом по стандартизации 2000-02-18. Определение твердости лако-красочного покрытия по карандашу

ISO 3745:2003 Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods for anechoic and hemi-anechoic rooms

Стандарт
  • формат pdf
  • размер 494.04 КБ
  • добавлен 23 августа 2010 г.
This International Standard is one of the ISO 3740 series, which specifies various methods for determining the sound power levels of machines, equipment and other sub-assemblies. When selecting one of the methods of the ISO 3740 series, it is necessary to select the most appropriate for the conditions and purpose of the test. General guidelines to assist in the selection are provided in ISO 12001 and ISO 3740. The ISO 3740 series gives only gener...

ISO/IEC 17007: 2009

  • формат pdf
  • размер 87.84 КБ
  • добавлен 07 сентября 2011 г.
First edition 2009-09- 15. Conformity assessment — Guidance for drafting normative documents suitable for use for conformity assessment. This International Standard provides principles and guidance on how to write normative documents, such as standards, technical specifications, codes of practice and regulations, such that they are concise and clear, especially in the context of any subsequent conformity assessment activity. Conformity assessme...

ISO/TS 16949:2009 Quality management systems - Particular requirements for the application of ISO 9001:2008 for automotive production and relevant service part organizations

  • формат djvu
  • размер 4.03 МБ
  • добавлен 03 ноября 2010 г.
ISO/TS 16949:2009 «Системы менеджмента качества - Особые требования по применению ИСО 9001:2008 для организаций-производителей серийных и запасных частей для автомобильной промышленности». - 39c. (на англ. языке).