API (American Petroleum Institute) Standards - (ENGL)

  1. Файлы
  2. Стандарты
  3. Стандарты Америки (AS)
  4. API
Стандарты Америки (AS)
Стандарт
  • формат pdf
  • размер 84.57 МБ
  • добавлен 09 января 2012 г.
API (American Petroleum Institute) Standards - (ENGL)
API 551 (1993)_Process Measurement Instrumentation.pdf ( 4206 KB)
API 552 (1994)_Transmission Systems.pdf (3162 KB)
API 553 (1998)_Refinery Control Valves.pdf (413 KB)
API 554 (1995)_Process Instrumentation and Control.pdf (5545 KB)
API 555 (2001)_Process Analyzers.pdf (3633 KB)
API 556 (1997)_Instrumentation and Control Systems.pdf (2423 KB)
API 557 (2000)_Guide To Advanced Control Systems.pdf (2867 KB)
API 560 (2001)_Fired Heaters for General Refinery Service.pdf (1245 KB)
Api 570 (2Nd 1998 54P) Piping Inspection Code.pdf (291 KB)
API 572 (2001)_Inspection of Pressure Vessel.pdf (9323 KB)
API 573 (1991)_Inspection of Fired Boilers and Heater.pdf (6180 KB)
API 574 (1998)_Inspection Practices for Piping System Component.pdf (4431 KB)
API 575 (1995)_Inspection of Pressure-Relieving Devices.pdf (1953 KB)
API 576 (2000)_Inspection of Atmospheric and Low-Pressure Storage Tank.pdf (5268 KB)
API 578 (1999)_Material Verification Program for Alloy Piping Systems.pdf (217 KB)
API 579 (2000)_API Recommended Practice.pdf (41092 KB)
Смотрите также

API 579-2/ASME FFS-2 2009 Fitness-For-Service Example Problem Manual

Стандарт
  • формат pdf
  • размер 3.93 МБ
  • добавлен 10 декабря 2011 г.
374 стр. American Petroleum Institute, The American Society of Mechanical Engineers, AUGUST 11, 2009 Fitness-For-Service (FFS) assessments in API 579-1/ASME FFS-1 Fitness-For-Service are engineering evaluations that are performed to demonstrate the structural integrity of an in-service component that may contain a flaw or damage or that may be operating under specific conditions that could produce a failure. API 579-1/ASME FFS-1 provides guidance...

API RP 2201 - 1995 Procedures for Welding or Hot Tapping on Equipment in Service (Eng)

Стандарт
  • формат pdf
  • размер 215.43 КБ
  • добавлен 18 января 2012 г.
American Petroleum Institute (API) Fourth Edition, September 1995. 23p. This publication covers the safety aspects to be considered when hot tapping, or when welding without hot tapping on in-service piping or equipment. It is not a substitute for job planning. A detailed, written procedure for hot tapping and welding should be prepared or reviewed before starting each job to ensure that all proper steps are taken.

API RP 2A-WSD-2007 Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms-Working Stress Design

Стандарт
  • формат pdf
  • размер 4.61 МБ
  • добавлен 13 декабря 2011 г.
288 стр. American Petroleum Institute, Errata And Supplement 3, October 2007 This publication serves as a guide for those who are concerned with the design and construction of new platforms and for the relocation of existing platforms used for the drilling, development, and storage of hydrocarbons in offshore areas. In addition, guidelines are provided for the assessment of existing platforms in the event that it becomes necessary to make a deter...

API RP 2T-2010 Planning, Designing, and Constructing Tension Leg Platforms

Стандарт
  • формат pdf
  • размер 2.16 МБ
  • добавлен 13 декабря 2011 г.
274 стр. American Petroleum Institute, Third Edition, July 2010 This recommended practice is a guide to the designer in organizing an efficient approach to the design of a tension leg platform (TLP). Emphasis is placed on participation of all engineering disciplines during each stage of planning, development, design, construction, installation, and inspection.

API RP 651 - 2007 Cathodic Protection of Aboveground Petroleum Storage Tanks (Eng)

Стандарт
  • формат pdf
  • размер 982.62 КБ
  • добавлен 18 января 2012 г.
American Petroleum Institute (API) Third Edition, January 2007. 46p. The purpose of this recommended practice is to present procedures and practices for achieving effective corrosion control on aboveground storage tank bottoms through the use of cathodic protection. It contains provisions for the application of cathodic protection to existing and new storage tanks. Corrosion control methods based on chemical control of the environment or the use...

API RР 577-2004 Welding Inspection and Metallurgy (Eng)

Стандарт
  • формат pdf
  • размер 5.86 МБ
  • добавлен 17 января 2012 г.
American Petroleum Institute (API). First Edition. October 2004. 114p. This recommended practice (RP) provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping. Common welding processes, welding procedures, welder qualifications, metallurgical effects from welding, and inspection techniques are described to aid the inspector in fulfilling...

API Spec 16A-1997 Specification for Drill Through Equipment

Стандарт
  • формат pdf
  • размер 5.97 МБ
  • добавлен 13 декабря 2011 г.
67 стр. American Petroleum Institute, Second Edition, December, 1997 This specification is formulated to provide for the availability of safe and functionally interchangeable drill through equipment utilized for drilling for oil and gas. Technical content provides requirements for performance, design, materials, tests and inspection, welding, marking, handling, storing, and shipping. This specification does not apply to field use or field testing...

API Spec 16С-1993 Specification for Choke and Kill Systems

Стандарт
  • формат pdf
  • размер 3.94 МБ
  • добавлен 13 декабря 2011 г.
63 стр. American Petroleum Institute, First Edition, Januaru, 1993 This specification was formulated to provide for safe and functionally interchangeable surface and eubsea choke and kill systems equipment utilized for drilling oil and gas wells. Other parts of the Choke and ЮН System not specifically addressed in this document shall be in accordance with the applicable sections of this specification. Technical content provides the minimum requir...

API Std 610 Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries

Стандарт
  • формат pdf
  • размер 6.99 МБ
  • добавлен 19 ноября 2011 г.
American Petroleum Institute / 01-Sep-2010 / 220 pages. Edition: 11th. Eleventh Edition (ISO 13709:2009 Identical Adoption). Scope. This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to overhung pumps, between-bearings pumps and vertically s...

AWS B4.0: 2007 Standard Methods for Mechanical Testing of Welds

Стандарт
  • формат pdf
  • размер 3.09 МБ
  • добавлен 09 декабря 2011 г.
154 стр. An American National Standard Approved by the American National Standards Institute May 2, 2007 7th Edition This specification establishes standard methods for mechanical testing of welds. The significance of each test, test apparatus, preparation of the test specimens, and the test procedure are described. Example test results sheets are provided. It is beyond the scope of this document to define the required mechanical properties or ac...
  • 2008 — 2024 «СтудМед»