Стандарт
  • формат pdf
  • размер 9.21 МБ
  • добавлен 03 декабря 2011 г.
API Std 618-1995 Reciprocating Compressors for Petroleum, Chemical, and Gas Industry Services
167 стр.
API STANDARD 618 FOURTH EDITION, JUNE 1995
This standard covers the minimum requirements for reciprocating compressors and their drivers used in petroleum, chemical, and gas industry services for handling process air or gas with either lubricated or nonlubricated cylinders. Compressors covered by this standard are of mod- erate-to-low speed and in critical services. Also covered are related lubricating systems, controls, instrumentation, inter- coolers, aftercoolers, pulsation suppression devices, and other auxiliary equipment. Compressors not covered are (a) integral gas-engine-driven compressors with single-acting trunk-type (automotive-type) pistons that also serve as crossheads and (b) either plant or instrument-air compressors that discharge at a gauge pressure of 9 bar (125 pounds per square inch) or less. Also not covered are gas engine and steam engine drivers.
Смотрите также

ANSI/API Std 610 Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries

Стандарт
  • формат pdf
  • размер 3.11 МБ
  • добавлен 08 декабря 2011 г.
220 стр. ELEVENTH EDITION, SEPTEMBER 2010 ERRATA, JULY 2011 ISO 13709:2009 (Identical), Centrifugal pumps for petroleum, petrochemical and natural gas industries This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to overhung pumps, between-b...

API RP 2201 - 1995 Procedures for Welding or Hot Tapping on Equipment in Service (Eng)

Стандарт
  • формат pdf
  • размер 215.43 КБ
  • добавлен 18 января 2012 г.
American Petroleum Institute (API) Fourth Edition, September 1995. 23p. This publication covers the safety aspects to be considered when hot tapping, or when welding without hot tapping on in-service piping or equipment. It is not a substitute for job planning. A detailed, written procedure for hot tapping and welding should be prepared or reviewed before starting each job to ensure that all proper steps are taken.

API RP 651 - 2007 Cathodic Protection of Aboveground Petroleum Storage Tanks (Eng)

Стандарт
  • формат pdf
  • размер 982.62 КБ
  • добавлен 18 января 2012 г.
American Petroleum Institute (API) Third Edition, January 2007. 46p. The purpose of this recommended practice is to present procedures and practices for achieving effective corrosion control on aboveground storage tank bottoms through the use of cathodic protection. It contains provisions for the application of cathodic protection to existing and new storage tanks. Corrosion control methods based on chemical control of the environment or the use...

API RР 577-2004 Welding Inspection and Metallurgy (Eng)

Стандарт
  • формат pdf
  • размер 5.86 МБ
  • добавлен 17 января 2012 г.
American Petroleum Institute (API). First Edition. October 2004. 114p. This recommended practice (RP) provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping. Common welding processes, welding procedures, welder qualifications, metallurgical effects from welding, and inspection techniques are described to aid the inspector in fulfilling...

API Std 610 Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries

Стандарт
  • формат pdf
  • размер 6.99 МБ
  • добавлен 19 ноября 2011 г.
American Petroleum Institute / 01-Sep-2010 / 220 pages. Edition: 11th. Eleventh Edition (ISO 13709:2009 Identical Adoption). Scope. This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to overhung pumps, between-bearings pumps and vertically s...

API Std 610: 2010 Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries

Стандарт
  • формат pdf
  • размер 3.11 МБ
  • добавлен 03 декабря 2011 г.
220 стр. ANSI/API STANDARD 610 ELEVENTH EDITION, SEPTEMBER 2010 ERRATA, JULY 2011 ISO 13709:2009 (Identical), Centrifugal pumps for petroleum, petrochemical and natural gas industries This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to ove...

API Std 616: 1998 Gas Turbines for the Petroleum, Chemical, and Gas Industry Services

Стандарт
  • формат pdf
  • размер 743.71 КБ
  • добавлен 04 декабря 2011 г.
100 cтр. API STANDARD 616 FOURTH EDITION, AUGUST 1998 This standard covers the minimum requirements for open, simple, and regenerative-cycle combustion gas turbine units for services of mechanical drive, generator drive, or process gas generation. All auxiliary equipment required for operating, starting, and controlling gas turbine units and for turbine protection is either discussed directly in this standard or referred to in this standard throu...

API Std 616: 2011 Gas Turbines for the Petroleum, Chemical, and Gas Industry Services

Стандарт
  • формат pdf
  • размер 5.72 МБ
  • добавлен 04 декабря 2011 г.
180 стр. API STANDARD 616 FIFTH EDITION, JANUARY 2011 This standard covers the minimum requirements for open, simple, and regenerative-cycle combustion gas turbine units for services of mechanical drive, generator drive, or process gas generation. All auxiliary equipment required for operating, starting, controlling, and protecting gas turbine units are either discussed directly in this standard or referred to in this standard through references...

API Std 617: 2002 Axial and Centrifugal Compressors and Expander-compressors for Petroleum, Chemical and Gas Industry Services

Стандарт
  • формат pdf
  • размер 2.4 МБ
  • добавлен 04 декабря 2011 г.
234 стр. Current status: Active Short description: Covers the minimum requirements for centrifugal compressors used in petroleum, chemical, and gas industry services that handle air or gas, including process gear mounted. Does not apply to fans or blowers that develop less than 34 kPa (5 pounds per square inch) pressure rise above atmospheric pressure; these are covered by API Standard 673. This standard also does not apply to packaged, integrall...

API Std 618-2007 Reciprocating Compressors for Petroleum, Chemical, and Gas Industry Services

Стандарт
  • формат pdf
  • размер 3.69 МБ
  • добавлен 04 декабря 2011 г.
API STANDARD 618 FIFTH EDITION, DECEMBER 2007 This standard is based on the accumulated knowledge and experience of manufacturers and users of reciprocating compressors. The objective of this publication is to provide a purchase specification to facilitate the procurement and manufacture of reciprocating compressors for use in petroleum, chemical, and gas industry services. The primary purpose of this standard is to establish minimum requirements...