Стандарты Британии (BS)
Стандарт
  • формат pdf
  • размер 97.57 КБ
  • добавлен 06 декабря 2011 г.
BS EN 10246-8: 2000 Non-destructive testing of steel tubes - Part 8: Automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections
14 cтр.
The European Standard EN 10246-8:1999 has the status of a British Standard
November 1999
This Part of EN 10246 specifies the requirements for automatic ultrasonic shear wave and Lamb wave testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections. The standard specifies acceptance levels and calibration procedures.
This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 10 mm.
European Standard EN 10246 "Non-destructive testing of steel tubes" comprises the Parts shown in annex A.
Похожие разделы
Смотрите также

BS EN 10246-10: 2000 Non-destructive testing of steel tubes - Part 10: Radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections

Стандарт
  • формат pdf
  • размер 295.42 КБ
  • добавлен 05 декабря 2011 г.
21 стр. The European Standard EN 10246-10:2000 has the status of a British Standard April 2000 This part of EN 10246 specifies the requirements for radiographic X-ray testing of the longitudinal or helically weld seams of automatic fusion arc-welded steel tubes for the detection of imperfections. The standard specifies acceptance levels and calibration procedures. European Standard EN 10246, Non-destructive testing of steel tubes, comprises the p...

BS EN 10246-14: 2000 Non-destructive testing of steel tubes - Part 14: Automatic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfections

Стандарт
  • формат pdf
  • размер 159.02 КБ
  • добавлен 05 декабря 2011 г.
16 стр. The European Standard EN 10246-14:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies requirements for automatic ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc welded (SAW) tubes, for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE : An alternative test method for the detection of laminar imperf...

BS EN 10246-15: 2000 Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections

Стандарт
  • формат pdf
  • размер 389.55 КБ
  • добавлен 05 декабря 2011 г.
16 стр. The European Standard EN 10246-15:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE 1: In the case of welded tube, an alternative ultrasonic testing specification for the detection of laminar...

BS EN 10246-16: 2000 Non-destructive testing of steel tubes - Part 16: Automatic ultrasonic testing of the area adjacent to the weld seam of welded steel tubes for the detection of laminar imperfections

Стандарт
  • формат pdf
  • размер 460.95 КБ
  • добавлен 06 декабря 2011 г.
16 стр. The European Standard EN 10246-16:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the ultrasonic testing of the area adjacent to the weld of welded steel tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE: This inspection may alternatively, in accordance with EN 10246-15, be carried out on longitudinal edges of...

BS EN 10246-17: 2000 Non-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections

Стандарт
  • формат pdf
  • размер 175.86 КБ
  • добавлен 05 декабря 2011 г.
12 стр. The European Standard EN 10246-17:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30...

BS EN 10246-3: 2000 Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections

Стандарт
  • формат pdf
  • размер 409.37 КБ
  • добавлен 06 декабря 2011 г.
18 стр. The European Standard EN 10246-3:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies the requirements for automatic eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes for the detection of imperfections. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of the tests. This Part of EN 10246 is applica...

BS EN 10246-5: 2000 Non-destructive testing of steel tubes - Part 5: Automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal im

Стандарт
  • формат pdf
  • размер 134.17 КБ
  • добавлен 06 декабря 2011 г.
16 cтр. The European Standard EN 10246-5:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies the requirements for automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded ferromagnetic steel tubes, with the exception of submerged arc welded (SAW) tubes, for the detection of longitudinal imperfections. The standard specifies acceptance levels, calibration procedures and gives gui...

BS EN 10246-6: 2000 Non-destructive testing of steel tubes - Part 6: Automatic full peripheral ultrasonic testing of seamless steel tubes for the detection of transverse imperfections

Стандарт
  • формат pdf
  • размер 122.96 КБ
  • добавлен 06 декабря 2011 г.
16 стр. The European Standard EN 10246-6:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies the requirements for automatic ultrasonic shear wave testing of seamless steel tubes for the detection of transverse imperfections. The standard specifies acceptance levels and calibration procedures. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 10 mm....

BS EN 10246-7: 2005 Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfections

Стандарт
  • формат pdf
  • размер 458.61 КБ
  • добавлен 06 декабря 2011 г.
14 стр. The European Standard EN 10246-7:2005 has the status of a British Standard October 2005 This part of EN 10246 specifies the requirements for automatic full peripheral ultrasonic shear wave (including phased array technique) and Lamb wave testing of seamless and welded steel tubes, with the exception of submerged arc-weld (SAW) tubes, for the detection of longitudinal imperfections. This European Standard specifies acceptance levels and ca...

BS EN 10246-9: 2000 Non-destructive testing of steel tubes - Part 9: Automatic ultrasonic testing of the weld seam of submerged arc welded steel tubes for the detection of longitudinal and/or transverse imperfections

Стандарт
  • формат pdf
  • размер 370.65 КБ
  • добавлен 06 декабря 2011 г.
14 стр. The European Standard EN 10246-9:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements for the automatic ultrasonic testing of the weld seam of submerged arc-welded (longitudinally or helically) tubes for the detection of imperfections oriented predominantly parallel to and/or at right angles to the weld seam. The standard specifies acceptance levels and calibration procedures. European S...