Европейский стандарт "Неразрушающие испытания - Ультразвуковой
контроль листового проката из аустенитных и аустенитно-ферритных
нержавеющих сталей размером 6 мм или более (методом отраженных
волн)" утвержден в сентябре 2001г.
BS EN 10307 (2001) Non-destructive testing - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method)
Стандарт
- формат pdf
- размер 207.13 КБ
- добавлен 10 января 2012 г.
Похожие разделы
Смотрите также
BS EN 10028-7: 2000 Flat products made of steels for pressure purposes - Part 7: Stainless steels (Eng)
Стандарт- формат pdf
- размер 876.69 КБ
- добавлен 21 декабря 2011 г.
This European Standard was approved by CEN on 3 September 1999. 54p. This European Standard specifies the requirements for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels, in thicknesses as indicated in Tables 6 to 9. The requirements in EN 10028-1 also apply.
BS EN 10222-5: 2000 Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels. (Eng)
Стандарт- формат pdf
- размер 275.65 КБ
- добавлен 15 декабря 2011 г.
This European Standard was approved by CEN on 3 September 1999. 20p. This part of this European Standard specifies the technical delivery conditions of forgings for pressure purposes made of stainless steels, including creep resisting steels.
BS EN 10246-13: 2000 Non-destructive testing of steel tubes - Part 13: Automatic full peripheral ultrasonic thickness testing for seamless and welded (except submerged arc welded) steel tubes
Стандарт- формат pdf
- размер 360.88 КБ
- добавлен 05 декабря 2011 г.
10 cтр. The European Standard EN 10246-13:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements for the full peripheral ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc welded (SAW) tubes, for wall thickness measurement. The standard specifies acceptance levels and calibration procedures. NOTE 1: Full peripheral testing does not necessarily mean that 100...
BS EN 10246-14: 2000 Non-destructive testing of steel tubes - Part 14: Automatic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfections
Стандарт- формат pdf
- размер 159.02 КБ
- добавлен 05 декабря 2011 г.
16 стр. The European Standard EN 10246-14:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies requirements for automatic ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc welded (SAW) tubes, for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE : An alternative test method for the detection of laminar imperf...
BS EN 10246-15: 2000 Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections
Стандарт- формат pdf
- размер 389.55 КБ
- добавлен 05 декабря 2011 г.
16 стр. The European Standard EN 10246-15:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE 1: In the case of welded tube, an alternative ultrasonic testing specification for the detection of laminar...
BS EN 10246-16: 2000 Non-destructive testing of steel tubes - Part 16: Automatic ultrasonic testing of the area adjacent to the weld seam of welded steel tubes for the detection of laminar imperfections
Стандарт- формат pdf
- размер 460.95 КБ
- добавлен 06 декабря 2011 г.
16 стр. The European Standard EN 10246-16:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the ultrasonic testing of the area adjacent to the weld of welded steel tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE: This inspection may alternatively, in accordance with EN 10246-15, be carried out on longitudinal edges of...
BS EN 10246-17: 2000 Non-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections
Стандарт- формат pdf
- размер 175.86 КБ
- добавлен 05 декабря 2011 г.
12 стр. The European Standard EN 10246-17:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30...
BS EN 10246-1: 1996 Non-destructive testing of steel tubes - Part 1: Automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness
Стандарт- формат pdf
- размер 707.35 КБ
- добавлен 05 декабря 2011 г.
18 стр. The European Standard EN 10246-10:2000 has the status of a British Standard July 1996 This Part of EN 10246 specifies the requirements for automatic electromagnetic testing of seamless and welded ferromagnetic steel tubes, with the exception of submerged arc-welded (SAW) tubes, for verification of hydraulic leak-tightness. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm...
BS EN 10246-2: 2000 Non-destructive testing of steel tubes - Part 2: Automatic eddy current testing of seamless and welded (except submerged arc welded) austenitic and austenitic-ferritic steel tubes for verification of hydraulic leak-tightness
Стандарт- формат pdf
- размер 425.88 КБ
- добавлен 06 декабря 2011 г.
16 cтр. The European Standard EN 10246-2:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies requirements for automatic eddy current testing of seamless and welded austenitic and austenitic-ferritic steel tubes with the exception of submerged arc-welded (SAW) tubes for verification of hydraulic leak-tightness. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations...