BS EN 758: 1997 Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non-alloy and fine grain steels - Classification (Eng)
This European Standard was approved by CEN on 1997-01-19. 16p. This
standard specifies requirements for classification of tubular cored
electrodes in the as-welded condition for metal arc welding with or
without a gas shield of non-alloy and fine grain steels with a
minimum yield strength of up to 500 N/mm2.
Похожие разделы
Смотрите также
Стандарт Американского Сварочного Общества AWS A 5.5-96/ASME SFA - 5.5 (ENG)
This specification prescribes requirements for the classification of low-alloy steel electrodes for shielded metal arc welding of carbon and low-alloy steels.
AWS A5.15-90/ASME SFA-5.14 Specification for Weld8ng Electrodes and Rods for Cast Iron (Eng)
This standard American Welding Society (AWS). 1990. 18p. This specification prescribes requirements for the classification of the following: (a) Rods for oxyfuel gas welding; (b) Electrodes for gas metal arc welding; (c) Electrodes for flux cored arc welding; (d) Electrodes for shielded metal arc welding.
AWS A5.25/A5.25M-97/ASME SFA-5.25 Specification for Carbon and Low-Alloy Steel Electrodes and Fluxes for Electroslag Welding (Eng)
This standard American Welding Society (AWS). 1997. 23p. This specification prescribes requirements for the classification of electrodes (both solid and composite metal cored) and fluxes for electroslag welding of carbon and low-alloy steels.
AWS A5.26/A5.26M-97/SFA-5.26 Specification for Carbon and Low-Alloy Steel Electrodes for Electrogas Welding (Eng)
This standard American Welding Society (AWS). 1997. 24p. This specification prescribes requirements for the classification of carbon and low-alloy steel electrodes for electrogas welding. It covers solid and composite (flux cored and metal cored) electrodes used with external gas shielding, and composite (self-shielded flux cored) electrodes used without external shielding
AWS A5.28-96/SFA-5.28 Specification for Low-Alloy Steel Electrodes and Rods for Gas Shielded Arc Welding (Eng)
This standard American Welding Society (AWS). 1996. 32p. This specification prescribes requirements for the classification of low alloy steel electrodes (solid, composite stranded, and composite metal cored) and rods (solid) for gas metal arc welding (GMAW), gas tungsten arc welding (GTAW), and plasma arc welding (PAW).
BS EN 12072: 2000 Welding consumables - Wire electrodes, wires and rods for arc welding of stainless and heat-resisting steels - Classification (Eng)
This European Standard was approved by CEN on 4 September 1999. 12 p. This standard specifies requirements for classification of wire electrodes, wires and rods for gas shielded metal arc welding, gas tungsten arc welding, plasma arc welding and submerged arc welding of stainless and heat resisting steels. The classification of the wire electrodes, wires and rods is based on their chemical composition.
BS EN 756: 2004 Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification (Eng)
This European Standard was approved by CEN on 2 January 2004. 16p. This standard specifies requirements for classification of electrode-flux combinations and all-weld metal in the as-welded condition for submerged arc welding of non alloy and fine grain steels with a minimum yield strength of up to 500 MPa. Classification can be made with solid wire electrodes or tubular cored electrodes. One flux may be classified with different electrodes. The...
BS EN 757: 1997 Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification (Eng)
This European Standard was approved by CEN on 1997-01-19. 14p. This standard specifies requirements for classification of covered electrodes based on the all-weld metal in the as-welded or stress relieved conditions for manual metal arc welding of steels with a minimum yield strength higher than 500 N/mm2.
BS EN ISO 636: 2008 Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification
The text of ISO 636:2004 has been prepared by Technical Committee ISO/TC 44 Welding and allied processes of the International Organization for Standardization (ISO) and has been taken over as EN ISO 636:2008 by Technical Committee CEN/TC 121 Welding the secretariat of which is held by DIN. This European Standard was approved by CEN (EUROPEAN COMMITTEE FOR STANDARDIZATION) on 5 April 2008 This International Standard specifies requirements for clas...