BS EN 10244-2: 2009 Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings (Eng)
This European Standard was approved by CEN on 20 December 2008.
20p. This part of this European Standard specifies the requirement
for coating mass, other properties and testing of zinc and zinc
alloy coatings on steel wire and steel wire products of circular or
other section.
Похожие разделы
Смотрите также
BS EN 10021: 2006 General technical delivery conditions for steel products (Eng)
This European Standard was approved by CEN on 25 November 2006. 20p. This European Standard specifies the general technical delivery conditions for all steel products covered by EN 10079 with the exception of steel castings and powder metallurgical products.
BS EN 10079: 2007 Definition of steel products (Eng)
This European Standard was approved by CEN on 13 January 2007. 48p, This European Standard defines terms for steel products according to: a) shape and dimensions; and b) appearance and surface condition.
BS EN 10222-1: 1998 +A1: 2002 Steel forgings for pressure purposes - Part 1: General requirements for open die forgings (Eng)
This European Standard was approved by CEN on 26 October 1997. Amendment A1 was approved by CEN on 14 March 2002. 18p. This Part of this European Standard specifies the general technical delivery conditions for open die steel forgings, ring rolled products and forged bars for pressure purposes
BS EN 10244-1: 2009 Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles (Eng)
This European Standard was approved by CEN on 13 December 2008. 10p. This European Standard specifies the requirements for the mass, other properties and testing of non-ferrous metal coatings on steel wire and steel wire products of circular or other cross-section
BS EN 10246-12: 2000 Non-destructive testing of steel tubes - Part 12: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections
14 cтр. The European Standard EN 10246-12:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements and the acceptance levels for magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections. This part of EN 10246 is to be used for the detection of surface imperfections on the entire or any part of the outer surface of tubes, excluding the e...
BS EN 10246-14: 2000 Non-destructive testing of steel tubes - Part 14: Automatic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfections
16 стр. The European Standard EN 10246-14:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies requirements for automatic ultrasonic testing of seamless and welded steel tubes, with the exception of submerged arc welded (SAW) tubes, for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE : An alternative test method for the detection of laminar imperf...
BS EN 10246-6: 2000 Non-destructive testing of steel tubes - Part 6: Automatic full peripheral ultrasonic testing of seamless steel tubes for the detection of transverse imperfections
16 стр. The European Standard EN 10246-6:1999 has the status of a British Standard November 1999 This Part of EN 10246 specifies the requirements for automatic ultrasonic shear wave testing of seamless steel tubes for the detection of transverse imperfections. The standard specifies acceptance levels and calibration procedures. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 10 mm....
BS EN 10324: 2004 Steel wire and wire products - Hose reinforcement wire (Eng)
This European Standard was approved by CEN on 1 July 2004. 15p. This document specifies the composition, dimensions and mechanical properties of high carbon steel wire for reinforcing high pressure hoses. It is applicable to wire used as a multiple parallel wire braided or spirally wrapped reinforcement in a rubber or synthetic hose which is made to withstand relatively high bursting pressure.
BS EN 12516-1: 2005 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells
114 cтр. The European Standard EN 12516-1:2005 has the status of a British Standard This European Standard was approved by CEN on 15 March 2005. This document (EN 12516-1:2005) has been prepared by Technical Committee CEN/TC 69 Industrial valves, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October...
BS EN 13480-1: 2002+A1: 2005 Metallic industrial piping - Part 1: General (Eng)
This European Standard was approved by CEN on 23 May 2002. Amendment A1 was approved by CEN on 12 May 2005. 18p. This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials (but initially restricted to steel) with a view to ensure safe operation.